Paper Tissue Flowers

Last week I discovered that I remembered how to make paper tissue flowers.  I guess I never really forgot; I just hadn't thought about making them.  But, I had this kinda cool looking gift bag that I wanted to dress up just a tad.  So I used a few sheets of coordinating paper tissue to stuff in the bag - as we do these days - and used the remainder for a flower.

First, I put six layers together of the tissue and cut a strip about 5" wide.  Then I fan folded the stack of tissue, with each folder about 1/2" wide or so.  Next I wrapped a bread tie around the middle, offsetting the fold of the wire just a bit so that I would have a longer "tail".  And yes, I said "bread tie".   A bread tie is just the right gauge wire for these.   If  you don't have a bread tie, go to the store, get some bread and take the tie.  You can use a clothes pin to hold the bread bag closed.

Round the ends so that what you have at this point is shaped like a tongue depressor.

Next fan out one side of the flower and pull up each sheet toward the middle.  Don't pull too hard, or you may tear the paper.  It's okay if you tear a little, the flower will be so tight it will not be noticed.

After you finish with that half, repeat on the other side.  Then fluff and pull until you like the way it looks.

Now you can attach it to the handle of a gift bag or onto the top of a gift. Wow - mine didn't look like this in 5th grade!

Boo Boo Bunny

                            
I found the instructions for making Boo Boo Bunnies many years ago in a book.  I used it then as a craft for the children that I was babysitting.  Now I include them as part of a baby shower gift.  They are so easy!  The idea is that when a little one has a boo-boo, you can grab the ice cube out of the freezer and pop it in the bunny and hold it against the boo-boo.

Materials needed:

One washcloth

Reusable ice cube

Ribbon

I have found that the thin cheaper washcloths work better for these.   The reusable ice cubes can be found at Bed Bath and Beyond or probably any kitchen-y type store.

First, open the washcloth, turn it so that it looks like a diamond, and start rolling it up from the corner like this: (Sorry for the white on white. It's what I had handy.)

Continue rolling until you have one long roll like this:

Then fold it in half like this: (It won't stay together this close, I had to tape it to take the picture)

Then flip the front two ends back like this: (yep, tape again)

If you use a thicker washcloth, you might want to use a rubber band to hold it still while you tie the ribbon around its "head" and fluff the ears, but with the thinner cloths, I can just hold it and tie it tight:

The last step is to drop in the ice cube in the body of the bunny:

And now you have a really cute adder for a baby shower gift that only took minutes to make!

Baby Shower Guest Book

Practicality is one of my strengths and one of my weaknesses.   I seem to dismiss things so quickly with a “what purpose does that really serve?”  I'm glad that I let my creative corner of the brain take over momentarily.  I was one of the hostesses for a friend’s baby shower recently.  This was to be her third child, but her first girl.   The mom-to-be is rather practical-minded as well, so I wanted to come up with a guest book that could be more than just a list of names or an alibi for someone’s whereabouts from 7-9 pm on the day in question. 

As her mother’s closest friends, I thought we could all write a message to the baby that she could enjoy when she got older – something funny like how to deal with big brothers or something sweet like looking forward to meeting her.  The book had to be unique and not over-the-top pink, so I went to work with the following items that I had on hand:

Basic Materials:

11 x 17 piece of cardboard, 1/16” thick (scavenged from the workplace)

Pastel/Baby patterned paper, 12” x 12”

Hole punch

Fine sandpaper

Brown Ink

Embellishments:

“This Book Belongs To:” rubber stamp

Vellum (for quotes)

Extra baby stickers

Extra cupcake topper*

I did have to purchase the binder rings used to bind the book.  They can be found anywhere that sells office supplies.  Be sure that you get rings that will have the diameter to accommodate the thickness of your final product and not be too tight.   This book was 1/2” tall containing 36 pages, and I used a 1” diameter set of rings.

I wasn’t sure that my Fiskars paper trimmer could handle cutting the cardboard, but I was able to cut on one side, then flip it over and cut again.  I cut two 4”x6” pieces of the cardboard for the front and back covers.  I selected the pale pink stripe as the cover pattern.  I cut four 4”x6” pieces of the paper, making sure that the stripes would be vertical for the finished product.   I attached the pink paper to the front and back of each cardboard piece.  Now for the hard part.

Turning one cover vertically, I measured from the top 1.5”  and from the left side .5” and penciled a small dot.  I repeated from the bottom, and then again on the other piece of cardboard.  Using the hole punch, I centered on the dot and made an indention onto the paper and cardboard.  I then called for the strong man of the house to complete the task.  He was able to muscle the hole punch and get all four holes punched, but I recommend eye protection next time.  There is probably a better tool out there, but I was making do with what I had available.  A lighter weight cardboard could also be used, but, hey, I couldn’t beat the price.  Feel free to leave a comment/suggestion.

Next I cut out the pages for the book.  I used all of the colors available in the pack just to make it fun.  I cut four pages of each, 3 15/16 ^“  x 5 15/16^”  so they would be just smaller than the covers and then rounded two corners.  I have a total of 36 pages, but adjust according to the number of folks attending as you see fit.

Now it is time to punch the pages.  Using one page with one of the covers, line up the page on the side where the holes are and punch through the cover and the page.  Now you have a template to use for the remaining pages.  If you have access to an adjustable three-hole or two-hole punch, that will probably go a lot faster than the single hole punch I used.

To make your own baby quotes is really simple.  Just type them up in a Word document with the font of your choosing and print it out using vellum.  Punch or cut out the quote. Be sure to use adhesive specifically for vellum when attaching to paper so it won’t show through.

Now that all of the pieces are ready, it is time for the fun stuff.

First, I used the sandpaper to scuff the edges and round the outer corners of the covers.  Next I inked the edges of the covers lightly. 

I also inked the extra cupcake topper and attached it to the front cover.  (You could use any kind of chipboard sticker or decoration)  Now you just put the rings through holes of the back cover, the pages, and finally the front cover.  I had a bookplate stamp, so I used it on the inside of the front cover.

Place a few baby quotes, stickers, and stamped images on random pages and you have a one-of-a-kind baby shower guest book! 

* Cupcake toppers instructions found here.